![]() Doesn't that suggest that something is off in the Icom IC-7100 transceiver settings in flrig? Thanks - David KD4E Sounds like the problem I had with my IC-7100. ![]() It works perfectly with the JS8Call software (USB-D). I fixed it by doing a factory reset and installing the latest firmware Modes, and nothing in USB or LSB modes (simce they are suppressed Had a dead modulator, so it would send unmodulated carrier in AM or FM Problem came from flrig or RF Systems' programming software, but I also Sounds like the problem I had with my IC-7100. It works perfectly with the JS8Call software (USB-D).ĭoesn't that suggest that something is off in the Icom IC-7100 Note: In all cases the rig TX power is set to 50w. On my external meter (this happens with only flrig and with both flrig & However, if I switch to USB or USB-D (the rig, flrig, & fldigi allĬhange & display correctly) the press Tune or CQ - there is no RF output Left - as it was when I previously closed it - I also tried PSK-31)īut the Mode setting on the upper left shows AM (apparently acquiredįrom flrig). If I open fldigi - the OpMode defaults to FSQ-6 (displayed on the bottom Power output is displayed on my external PWR/SWR meter. Problem: I see no RF power out in USB or USB-D using flrig on aĭetail: With just flrig open and Mode set to AM I can press PTT and To: No RF power out in USB or USB-D using flrig & fldigi I fixed it by doing a factory reset and installing the latest firmware from Icom. I'm not sure whether the problem came from flrig or RF Systems' programming software, but I also had a dead modulator, so it would send unmodulated carrier in AM or FM modes, and nothing in USB or LSB modes (simce they are suppressed carrier). I prefer the comment section here or in YouTube over e-mail because your comments and questions will help others as well.Sounds like the problem I had with my IC-7100. If you have any questions, comments or solutions, please comment below. By practicing I hope too improve my memory, fist and typing.Ĭoming Soon – I will have a video, article and pictures of my campers Hi-Q mobile antenna installation, the updated solar installation and an update on my Tarheel 200A mobile antenna. Since my stroke I am alternating between the software and my paddle, decoding what I can with the help of notepad. If you have any questions, please ask below. "Unlink from " must be used in the Icom menu.This configuration leaves your USB cable open for rig control in your logging program. ![]() For Icom transceivers: Use a CI-V cable for rig control in Fldigi (RigCAT) and then a CW interface for DTR keying.See second image below.įdigi Configuration Screenshots For ACLog In Fldigi go to Fldigi configuration>Logging>N3FJP logs and enable connect.You may be able to enable it later, but get Fldigi sending real CW first. Many users have reported much, much higher speeds. I have not had any trouble keying at 12-18wpm. Right now I am using a CW interface, but have tried it different ways and it works great. You can use a CW interface (Separate Keying Serial Port), but you can also use a USB serial (COM) port for DTR keying.For integrating these two programs have a look at Icom 7610 Rig Control N3FJP Amateur Contact Log and Fldigi.Just for kicks I thought I would go back and see how Fldigi real CW works with ACLog on my Windows PC. I only noticed this Fldigi update when I was preparing a video and article on MacLoggerDX Fldigi AutoLog Script with PTT App. See my Icom 7610 and Icom 7300 Screen Capture Pages for internal menu settings on these radios.Put the radio in CW mode and you can use your CW filters.I hear it works great on all three platforms. It is available for Windows, Mac and Linux. A good informational source for Fldigi is the WinFldigi forum on Groups.io. I am using a CW USB Keying Cable, but there are other options. This feature came out a little while back, but with everything going on I missed it. ![]() This is new to me, Fldigi real cw via DTR keying.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |